Question 42: Which two configurations can you apply to a port so that it. Question 41: Which command prevents all access ports on a switch from sen. Question 40: What Cisco Catalyst switch feature can be used to define por. Question 39: Which security feature inspects ARP packets based on valid I. Question 38: After UDLD is implemented, a Network Administrator noticed t. Question 37: In the hardware address 0a, what does 07.ac repr.
#Rspan mac address learning mac#
Question 36: Which two statements about dynamic MAC address learning are. Question 35: Which two commands or command sequences configure a switch s.
Question 34: Which feature is automatically enabled when a voice VLAN is. Question 33: You have configured switches A and B in a network. Question 32: Which two statements about the local user database are true?. Question 30: Which command do you enter to enable Dynamic ARP Inspection. Question 29: You have recently deployed an access switch with two fiber c. Question 28: Which statement is true about Stackwise?. Question 27: What will be behavior of an access port when a tagged packet. Question 26: Which feature places a port in an err-disabled state when it. Question 25: The output displayed below is a result of what command? Inte. Question 24: Which two statements about VRRP are true? (Choose two.). Question 22: What happens if we add "line" on AAA command?. Question 21: Which two prerequisites for HSRP to become active on an inte. Question 20: If a network engineer applies the command mac-address-table. Question 19: Which command produced the following output? (Exhibit). Question 18: Which command enables you to determine whether any interface. Question 17: Which type of MAC address can be dropped by a switch that is. 3 comment Question 16: Which two commands display the VLANs that are present in the. Question 14: What command disables 802.1x authentication on a port and pe. Question 13: Inter-VLAN routing has been operating successfully for sever. Question 12: What Cisco switch feature allows IP phones to be automatical. Question 11: When executed on a HSRP group member named Router 10, what e. Question 10: (Exhibit) Refer to the exhibit. Question 8: Instructions Enter IOS commands on the device to verify netw. Question 7: At which OSI layer does STP operate?.
#Rspan mac address learning Pc#
Question 6: A network engineer is trying to deploy a PC on a network. Question 4: Which statement describes the result of issuing the spanning. Question 3: A company has the following network infrastructure. Question List (501q) Question 1: Which feature can you enable on your network to most effecti. The RSPAN VLAN ID separates the sessions. It is also possible to have multiple RSPAN destination sessions throughout the network, monitoring the same RSPAN VLAN and presenting traffic to the user. That is, multiple RSPAN source sessions anywhere in the network can contribute packets to the RSPAN session. It is normal to have multiple RSPAN VLANs in a network at the same time with each RSPAN VLAN defining a network-wide RSPAN session. If you assign an RSPAN VLAN ID in the extended VLAN range (1006 to 4094), you must manually configure all intermediate switches. STP can run on RSPAN VLAN trunks but not on SPAN destination ports.Īn RSPAN VLAN cannot be a private-VLAN primary or secondary VLAN.įor VLANs 1 to 1005 that are visible to VLAN Trunking Protocol (VTP), the VLAN ID and its associated RSPAN characteristic are propagated by VTP. RSPAN VLANs must be configured in VLAN configuration mode by using the remote-span VLAN configuration mode command. RSPAN VLAN traffic only flows on trunk ports. No MAC address learning occurs on the RSPAN VLAN. It has these special characteristics:Īll traffic in the RSPAN VLAN is always flooded.
Only ports which have a device connected and active will show the mac address detail.The RSPAN VLAN carries SPAN traffic between RSPAN source and destination sessions. With the above command, one can figure out which Mac address is on which port of catalyst switch. Switch# show mac-address-table | include 0009.aabb.06e9 Or if you know the mac address and want to know which port the mac address is coming from, use the following command Switch# show mac-address-table | include Fa0/5 If you know the switch port you can use the following command Only ports which have the device connected and active will show the mac address detail. mac address of the connected device) and port number. The mac address or CAM table shows the Vlan associated with the port, MAC being learned on the port (i.e. With the command, you can figure out which MAC address is on which port. Total Mac Addresses for this criterion: 5
0 kommentar(er)
